Litter robot blue light blinking but not full. The cat sensor may be small, but is still an important part o...

Dump all litter unplug robot from wall (not just po

How to fix the blinking blue light on the litter robot open air that says the tray is full when it’s not. I hope this helps.Litter-Robot 3: Yellow & Red or Blue & Red Flashing (Motor Over-torque) If Litter-Robot 3 Globe becomes jammed or overloaded when rotating clockwise, the Motor will stop and reverse for 5 seconds. The unit will start to cycle again after 15 seconds, to attempt to return to the Home Position. If after three attempts, the unit is unable to cycle ...So I am watching my cousins 2 cats because she is out of town for another week. I was wondering if anyone here has ran into a similar situation. The robot will not stop flashing blue , thinking the waste needs changing. I have reset the system multiple times, cleaned the lense and lense cover, and recalibrated the sensor. Nothing has worked.To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully ...#1 Blue Light The most common light signal you have to deal with when you have a Robot litter box is the blue light. It's also the easiest to troubleshoot. A solid blue light means that your unit is ready to use and everything is working as it should. On the other hand, a blinking blue means that the waste drawer is full.Wait 1 minute. Plug it back in. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty buttons. Enter onboarding mode again by pressing both ...Press the Reset button twice. Make sure any dirt or obstacles is not blocking the sensor. If the blue light is blinking now, the drawer is somehow removed. Now, if the sensors are clean, there is no dust in the drawer. Maybe you need to repair your device from a service center.Jan 22, 2021 · Hi , I have bought my litter robot 5 months ago . Yesterday it started to blink the blue light but the drawer was completely empty so I pressed reset and it was ok . Today same thing happened but when i presed the reset buton ,the cycling indicator started to rapidly blink. I checked on your forum for help and did a full sensor clean up I tried to reset but couldn’t. Please I need help ! To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully ...To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully ...Litter-Robot 3: Yellow & Red or Blue & Red Flashing (Motor Over-torque) Litter-Robot 3: Yellow and Blue Light (8-Hour Sleep Mode) Litter-Robot 3: Yellow Flashing Quickly (Pinch Sensor) Litter-Robot 3: Yellow Flashing Slowly (Bonnet Removed & Cat Sensor) Litter-Robot Power Supply Specifications Litter-Robot Return InstructionsJust a quick video to show how I use cheap, easy to find 8 gallon trash bags (any brand 8 gallon will work) and a rubber band to fit my litter robot 3’s coll...According to the California Department of Motor Vehicles, a blinking or flashing yellow light means that drivers should proceed with caution. Unlike a blinking red light, a blinking yellow light does not require drivers to stop, but it does...1. When your cat exits Litter-Robot, a timer counts down, allowing the litter to clump before a clean cycle begins. 2. During the clean cycle, the globe slowly rotates. The patented sifting process separates the clumps from …Tldr: my robot has a blue flashing light and none of the buttons do anything, only on/off. I’ve tried the basics. I’ve had the litter robot for a few years, but can’t remember if it’s a 1 or 2 model. I’ve encountered an issue I can’t fix. It started with the quick flashing yellow light (pinch detector issue). When I press the rest button, the blue light goes out and the yellow light flashes quickly. I have checked and cleaned the pinch sensor, no change. If I press reset repeatedly the blue and yellow lights will alternate: blue flashing RESET yellow flashing RESET blue flashing, etc. I can't get the unit to cycle at all, it won't empy, it is ...So woke up this morning with litter robot 4 offline. The big light is solid blue with the little light flashing blue. How do I reconnect it? I pressed the wifi button once, goes to solid light yellow, pressed it again and goes back to blinking blue. If I press the wifi for 3 seconds, goes to flashing yellow, but nothing happens on the app. It ...Unsuccessful: If your unit is not displaying a solid blue light after returning to home position, or cannot complete the cycle, your unit needs to be repaired. Issue not resolved? To repair your Litter-Robot, you will need a Motor Assembly or a new base.Slow blue light --> fast yellow flashing light. I have a pretty old LR 3 (non-Connect, serial # 028957). I replaced the DFI and pinch detect terminals about 1.5-2 years ago and it's been working pretty well since then. A few days ago, the unit stopped cycling entirely. The blue DFI light started blinking even when the tray was empty, and after ... 1.) Leave your unit powered ON with the blue blinking light engaged and unplug your power supply from the base 2.) Wait 10 seconds, then plug the unit back in. 3.) Allow the unit to complete a start-up cycle. If the light is solid blue, the code has been successfully cleared. If the light is still blinking, let's proceed with troubleshooting.Jan 13, 2023 · The Litter Robot is a self-cleaning litter box that makes life easier for cat owners. It has a built-in sensor that detects when your cat has used the litter box, and then automatically rotates and separates the clumps into a waste drawer. The blue light on the Litter Robot indicates that it is in standby mode or working properly. The little green light on the back of your HP desktop indicates the health and well-being of your power supply unit. Normally this light glows a steady green, but damage to the PSU or power issues can cause it to blink instead. This type of...The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit should start its cleaning cycle and goes back ...A few days ago, the blue light won't stop blinking after a cycle. Initially it would go solid blue after reset/cycle, but now it's constantly blinking. I tried following the DFI troubleshooting video here: https://www.youtube.com/watch?v=YQJz0VOBzkw in cleaning off the sensor and resetting the sensor, but nothing works.I have this same problem after 2 years. I’ve contacted customer support, and they only offered tips for the opposite problem (the blue light flashing as if it is full when it is not). I even asked right out if I need to buy and replace the sensors, but again, I was just given links to their unhelpful “troubleshooting” pages.So I took it apart cleaned it and put it all back together. Now all it will do is flash the blue light! The drawer is empty, the bag is not in the way, and it will not cycle at all, even when unplugged and plugged back in. Troubleshooting said to wipe the sensor with a qtip, so I wiped down the area, although I don't really see a black spot ... If Litter-Robot 4 displays a blue light bar with a blinking blue light adjacent to the Connect button, this indicates that the unit is connecting to the app or has disconnected and is trying to reconnect but has not successfully reconnected.Turned machine back on and it shows the yellow light on cycle but nothing happens and then the blue yellow red lights come back on. Thank you for your reply. This could be a motor problem or a malfunction from the circuit board. Turn the unit off. Remove the bonnet and globe.The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. To test your changes, power the unit off and then on. Allow the unit to complete the start‐up cycle and return Home with a solid blue light. Your unit is operating normal.Successful: If your Litter-Robot displays a blue light bar after cleaning the sensors, you've been successful. Unsuccessful: If you are still seeing a blue light bar flashing, please follow these troubleshooting steps. Issue not resolved? Next, let's make sure your firmware is up-to-date.Litter-Robot 3: Yellow & Red or Blue & Red Flashing (Motor Over-torque) If Litter-Robot 3 Globe becomes jammed or overloaded when rotating clockwise, the Motor will stop and reverse for 5 seconds. The unit will start to cycle again after 15 seconds, to attempt to return to the Home Position. If after three attempts, the unit is unable to cycle ...This video will show you what the DFI sensors are. What do they do, where are they, how they work and how to clean them. Also a quick tip on fixing a common ...Slow blue light --> fast yellow flashing light. I have a pretty old LR 3 (non-Connect, serial # 028957). I replaced the DFI and pinch detect terminals about 1.5-2 years ago and it's been working pretty well since then. A few days ago, the unit stopped cycling entirely. The blue DFI light started blinking even when the tray was empty, and after ... When I switch the Robot off/on the blue light flashes (but the litter is not full) then if I then press the RESET button (or any other button) the yellow light (2 flashes per second) stay on. I cannot get the system to come off the yellow light fault. Please can someone help! pjutras January 29, 2019, 7:58pm 5Super Eco Wash – This low-temperature Ecobubble cycle helps reduce power consumption. 15′ Quickwash – For lightly soiled garments in less than 2.0kg that you want to wash quickly. This cycle usually lasts approximately 15 minutes and uses up to 40 °C. When using this cycle, use less than 20g of detergent.Reboot your router. Completely close the Litter-Robot app. While the unit is at the Home position with the solid blue light, unplug your unit from the BASE, not the wall. Wait 15 seconds, plug it back in, and allow it to cycle until the solid blue light comes on (“Ready” status). Open the app and follow the steps.Litter-Robot 4: Light Codes Guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more. Blue with flashing yellow WiFi. A Shark Robot Vacuum can be reset by turning it upside down and pressing the power button (located on the side) for at least 10 seconds. The unit should power off. Wait a minimum of 10 seconds, then press the power button once. A Shark Robot vacuum can also be reset by the app. Simply access the Settings menu and select Factory Reset from the ...To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully ...Jan 13, 2023 · The Litter Robot is a self-cleaning litter box that makes life easier for cat owners. It has a built-in sensor that detects when your cat has used the litter box, and then automatically rotates and separates the clumps into a waste drawer. The blue light on the Litter Robot indicates that it is in standby mode or working properly. Also, blinking blue is a drawer fault. Make sure the drawer is inserted properly and the liner is not interfering with the drawer full sensor or motion of the globe. Alocasia_Sanderiana • 4 mo. ago. Later today I will go ahead and fully empty the globe and try to cycle. I will also empty the litter drawer completely and try that.Our litter robot was Flashing Yellow Slow & Fast, then Fast Flashing Blue despite being empty and lastly just Random Lights. Watch for the solution to this, ...Litter-Robot 3 models (Litter-Robot 3 and Litter-Robot 3 Connect) are equipped with a Drawer Full Indicator sensor (DFI sensor). It is located above the Waste Drawer and it checks if the drawer is full each time the Globe returns to the Home position. The Control Panel displays a flashing blue light when the DFI is activated.Brand new Litter Robot flashing Blue - Red Sequentially. Hey everyone - we got a Litter Robot and it started flashing Blue then Red immediately after running a cycle. Chatted with customer service and they said it was an over-torque issue. They sent a new base yet I'm getting the same flashing Blue - Red lights.No, I'm not overfilling the litter. No, I have the drawer bag well below the sensors), no issues shown on the app. Try manual cycle, no response, go downstairs and manually press the cycle button and get fast yellow blinking light. Wtf. Power off, back on, blue light blinking slowly, press cycle, yellow fast blinking light again.To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a startup cycle. If the light is solid blue, the code has been successfully cleared.Ours did this even after replacing the drawer sensors. After taking it completely apart, we realized that the cat sensor in the back under the drawer was too tight. It was causing it to fault every time it cycled. After some adjustment, it is now working like it should. Try to clean off the drawer sensors and adjusting the cat weight sensor.Thanks for the reply. I have ensured the 2 connectors are indeed touching and if I could post images on here I could show you. When I switch the Robot off/on the blue light flashes (but the litter is not full) then if I then press the RESET button (or any other button) the yellow light (2 flashes per second) stay on.Wait 1 minute. Plug it back in. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty buttons. Enter onboarding mode again by pressing both ...Step 10: Manual Cat Sensor Activation. Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn off and the red light should come on. You've activated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allow the Wait Time (3, 7, or 15 …Successful: If your unit returned home and displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a blue light bar flashing after reseting at …The cat sensor may be small, but is still an important part of your Litter-Robot Open Air III. Without this small component, your robot won't detect when your cat is inside the litter. Although the sensor is not prone to defects, it is pretty sensible and you could find yourself one day with a Red.According to the California Department of Motor Vehicles, a blinking or flashing yellow light means that drivers should proceed with caution. Unlike a blinking red light, a blinking yellow light does not require drivers to stop, but it does...According to the California Department of Motor Vehicles, a blinking or flashing yellow light means that drivers should proceed with caution. Unlike a blinking red light, a blinking yellow light does not require drivers to stop, but it does...Hi, So I am having this issue again!!! My litter robot 3 had been flashing blue light and then yellow light (very fast) after pressing the reset button. I’ve read some troubleshooting to check for the metal pinch bars to be in contact all the time. I’ve tried to clean it and it appears to be in contact as well. The pin is not corroded as well. Please …The Litter Robot 3 control panel provides the main user input /(buttons) and output (LEDs) for the robot. Aside from the main power light, there are three lights on the Litter Robot 3 control panel, which are blue (ready button), yellow (cycling button) and red (timing button). There are also four buttons which are "power", "cycle", "empty" and ...Jul 22, 2020 · Litter-Robot 3 flashing red light A solid ruby light on your Litter-Robot 3 control panel means that the cat sensor was activated by to cats entered an globe while the unit was ready for getting. This unit is counting down to a clean cycle, depending on your set wait time (3, 7, instead 15 minutes). If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more. Blue with flashing yellow WiFiView the Litter-Robot 3 Waste Drawer Liner Installation Video. To change the drawer liner in Litter-Robot 4, pull out the drawer and dispose of the soiled liner. Open a new waste drawer liner and wrap the edges over the rim of the waste drawer. Push the remainder of the bag into the bottom of the waste drawer. Check out the Litter-Robot 4 …Successful: If your unit returned home and displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a blue light bar flashing after reseting at …1.) Leave your unit powered ON with the blue blinking light engaged and unplug your power supply from the base 2.) Wait 10 seconds, then plug the unit back in. 3.) Allow the unit to complete a start-up cycle. If the light is solid blue, the code has been successfully cleared. If the light is still blinking, let's proceed with troubleshooting. The Litter-Robot does not really go on sale, but you can use our affiliate link above to save $25 off the top. But there are also reconditioned units that offer great value since you’ll receive a manufacturer-approved product at a lower Litter-Robot price!Another reason for the flashing yellow light could be a full waste drawer. If the waste drawer is full, the Litter-Robot will not be able to cycle properly. Empty the waste drawer and ensure it is properly inserted back into the unit. Additionally, the flashing yellow light could indicate a problem with the globe rotation. This could be caused ...Litter-Robot 3: Reset Button. The Reset button will reset your Litter-Robot's Cat Sensor. You can think of the Cat Sensor as the scale and the Reset button as a way to zero the scale. IMPORTANT: Any time you do anything that affects the weight or placement of the unit, including adding or removing litter, emptying the Waste Drawer, or moving or ...Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue Solid A solid blue light means Litter-Robot is ready and safe for kitty to use. Blue Flashing If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Blue with Flashing Yellow WiFiLitter-Robot 3 flashing red light A solid ruby light on your Litter-Robot 3 control panel means that the cat sensor was activated by to cats entered an globe while the unit was ready for getting. This unit is counting down to a clean cycle, depending on your set wait time (3, 7, instead 15 minutes).LG Craft Ice is Not Round: Causes and How to Fix; LG French Door Refrigerator Not Cooling: How to Fix; Litter-Robot Blue Light Blinking: How to Fix; LG Refrigerator Not Cooling ( Freezer Working): How to Fix; Ring Solar Panel Not Charging: Causes and Fixes; Arlo Solar Panel Not Charging: Causes and Fixes; Simplisafe Motion …The yellow light flashing quickly is due to the anti-pinch feature. The Anti-Pinch safety feature is two pin connected to the motherboard that must touch each other continuously. If they are separated, you will have an alarm (yellow blinking light). The Anti-Pinch safety is located in the top back left of the Litter-Robot base.Here’s how to go about clearing the cache: Find “Settings” on your mobile device and select it. Scroll down to “Apps” and select the Hue Bridge app when you find it. Tap on “Storage” and you’ll see the amount of data stored in the cache. You’ll also see a prompt to clear the cache. Tap “Tap on “Clear cache.”.I followed this guide (Litter-Robot III Open Air - Blue Blinking Light) multiple times with following outcomes: Unplugging robot for 10 seconds (or even 15 minutes) does not help the problem; There are no debris on the RFI lenses; Unit goes to solid blue with the waste drawer removedOriginally I've been getting the blinking blue light censor, (until I completely removed cleaned and reattached the dfi cases) but now it's switched to unresponsive solid Yellow (Power button doesn't work.) I've found when I unplug it for a few minutes with the waste drawer completely removed, the blinking blue light returns.So I took it apart cleaned it and put it all back together. Now all it will do is flash the blue light! The drawer is empty, the bag is not in the way, and it will not cycle at all, even when unplugged and plugged back in. Troubleshooting said to wipe the sensor with a qtip, so I wiped down the area, although I don't really see a black spot ...Super Eco Wash – This low-temperature Ecobubble cycle helps reduce power consumption. 15′ Quickwash – For lightly soiled garments in less than 2.0kg that you want to wash quickly. This cycle usually lasts approximately 15 minutes and uses up to 40 °C. When using this cycle, use less than 20g of detergent.To confirm the DFI has failed when there is a flashing blue light, leave the LR as is powered on, pull the waste drawer out and use your phones camera to look at the Left side DFI board, you should see 4 steady flashing lights on your camera screen, (from The areas marked D1, D3, D5, and D7) on the Emitter board. Step 10: Manual Cat Sensor Activation. Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn off and the red light should come on. You've activated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allow the Wait Time (3, 7, or 15 minutes ...I receive really interesting update from Litter-Robot. To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI.1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully cleared. If the light is still blinking, let's proceed with troubleshooting.Tldr: my robot has a blue flashing light and none of the buttons do anything, only on/off. I’ve tried the basics. I’ve had the litter robot for a few years, but can’t remember if it’s a 1 or 2 model. I’ve encountered an issue I can’t fix. It started with the quick flashing yellow light (pinch detector issue). Jan 25, 2023 · Step 1: Check the Power. The first thing to do when it comes to troubleshooting a Litter Robot that is stuck mid-cycle is to check the power. Make sure the unit is plugged in and the power cord is securely connected to the unit and the outlet. If the power cord is loose, securely reconnect it. If the outlet is not functioning, try plugging the ... Super Eco Wash – This low-temperature Ecobubble cycle helps reduce power consumption. 15′ Quickwash – For lightly soiled garments in less than 2.0kg that you want to wash quickly. This cycle usually lasts approximately 15 minutes and uses up to 40 °C. When using this cycle, use less than 20g of detergent.The litter robot 3 blinking blue light indicates that the waste drawer is full and needs to be emptied. To resolve this issue, simply empty the waste drawer and restart the unit, and the blinking light should stop. ... In this article, we will discuss the litter robot 3 blinking blue light and how to troubleshoot it. Credit: aichatgpt.co.za ...Fill your Litter-Robot to the fill line with litter and then perform a hard reset on your unit. Here’s how to do a hard reset on your Litter-Robot 4: Press and hold the Reset and Power buttons for 3 seconds. The light bar will flash red then go through a sequence of red, blue and green lights then begin a cycle.Originally I've been getting the blinking blue light censor, (until I completely removed cleaned and reattached the dfi cases) but now it's switched to unresponsive solid Yellow (Power button doesn't work.) I've found when I unplug it for a few minutes with the waste drawer completely removed, the blinking blue light returns.The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to. There's a lot of dust and debris which can cause issues, which leads to the robot not ...It's really annoying. Thank you for helping, it's appreciated. both errors are linked to the 4 pin connector (blue light is the DFI yellow light is the pinch sensor - same component) I would open the motor compartment, unplug and replug the 4 pin connector. Might be loosen. Thank you! I will give that a try :D.Apr 4, 2020 · The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit should start its cleaning cycle and goes back ... 3. Low Water Pressure. If you have low water pressure in your home, the LG Craft Ice will not offer round ice. To make the ice spherical, you will need a minimum pressure of 21 psi. Before dealing with this issue, test the pressure of the water by placing an 87-ounce cup under the dispenser.Power TheDevice “On”. If your device doesn’t cycle automatically, Press “Cycle.”. If it cycles and the light turns blue. Be sure your device is running normally. But be confirmed at least after two to three cycles. If it is still not working properly, Try Recalibrating the sensors. It may work on the issue.The robot is away from walls and perfectly level. There is nothing under the robot. It's filled to the line with normal clumping cat litter. I've tested with an empty drawer and full drawer, it makes no difference. If I reset the light back to blue and have it cycle, it stops mid-cycle, returns to original position, and red/blue appears again.Dec 3, 2021 · The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to. There's a lot of dust and debris which can cause issues, which leads to the robot not ... Emptying the Waste Drawer when indicated is important to ensure that your Litter-Robot continues to cycle automatically. Troubleshooting. A flashing Blue Light is normal, indicating the Waste Drawer is full. If your unit displays a flashing blue light or you received a “drawer full” notification in the Whisker App, please follow these steps:The tray's empty and the light still blinks with or without a bag. None of the buttons work and there's no start up cycle when I switch it on and off. The lights flash sequentially when it boots up, but it always settles on a blinking blue light. I can still switch the Litter Robot on and off via the app but I can't do anything else.. See full list on techevery.net Came back in an hour later and the blue light for w A blinking check engine light means that the onboard diagnostic system detected a problem with the engine. A blinking light, rather than a steady light, often indicates a serious engine misfire. A driver with a blinking light should head di...If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app. You can now proceed with the onboarding process within the Whisker App to finalize connection. Just received a few days ago the Robot Litter III Dive into How To Fix Litter Robot Blue Light Blinking, their meanings, and the solutions to ensure an experience for cat owners. With both options, you will get an additional warranty, just in case!...

Continue Reading